- 品牌/商標：Cyntec
- 企業類型：制造商
- 原產地：臺灣
1206 size pt-smd thermal sensor
1206型pt smd熱傳感器
1 scope范圍
this specification applies to 1.6mm*3.2mm size PT-SMD thermal sensor for use in temperature measurements，compensation and over-temperature protection
本規格適用于尺寸為1.6毫米* 3.2毫米，型號1206 pt smd的熱傳感器，主要用于溫度測量，修正和過熱保護
2 type designation 機型名稱
S E 1 0 2 0 5
（1)series No. 系列編號
（2）Ice point resistance : 冰點電阻
102=10x102 =1000Ω 公差:102=10x102 =1000Ω
（3）TCR /TOLERANCE : 電子溫度系數/公差
0: 3850/B
（4）package type 包裝規格
5:surface mount 表面黏著方式
3 specifications規格
3-1 typical resistance value (@ 0℃) :1000±1.2Ω
標準的電阻值 0度 :1000±1.2Ω
3-2 typical temperature coefficient of resistance :3850ppm/℃
標準的電阻溫度系數 :3850ppm/℃
3-3 typical thermal response time t0.9 (at 1m/sec Aiir,room temperature) :6sec
標準的熱響應時間t0.9(1米/秒,空氣,室溫) :6sec
3-4 norminal applied current :1mA
正常應用電流 1毫安
3-5 typical dissipating constant (at 1 m/sec Air , room temperature) :3.5mW/℃
標準的散熱系數(1米/秒,空氣,室溫) 3.5mW/℃
3-6 operating temperature range] :－55℃ to +125℃
工作溫度范 ：－55℃ to +125℃
3-7 temperature deviation :B class
溫度偏差 Δ T=±( 0.3+0.005 ltl )℃
4 outline drawing 外形圖；輪廓圖
5 .characteristic特征
5-1-1 insulation resistance
1000M ohm or more
絕緣電阻,1000M 歐母或更多
the pt-smd shall be cramped in the metallic block and tested , as shown below :
pt smd應夾在金屬塊中間進行測試, 與所示如下：
test voltage: 測試電壓 insulation prate絕緣空間
pressure rod 加壓桿(金屬) spring 彈簧
measurement point測量點A test sample 試樣
substrate基板 metal block 金屬塊
protection film 保護膜 measurement pointB測量點 B
5-1-2 voltage proof耐電壓
without damage by flashover ,fire or breakdown.etc.沒有受任何損壞的情況下
the pt-smd shall be tested as shown in paragraph 5-1-2. pt smd 要接受如下幾種測試
test voltage:100v a.c. r.m.s for 1minute 測試電壓:100 v交流a.c. r.m.s 1分鐘
after above each item test, valuation of item 3-1 should be within0.12%
當以上所有的測試完成后,評估項目3-1的公差應該在0.12%以內。
5-2 mechanical機械的
5-2-1 solderability 可焊性
a new uniform coating of solder shall cover minimum of 95%of the surface being immersed
一個新涂層必須均勻油浸95%的表面，
temperature of solder :245±5℃
焊料的溫度 :245±5℃
immersion duration :2±0.5 sec
浸漬時間 :2±0.5 sec
5-2-2resistance to soldering heat 耐焊接熱
shall be satisfied in any one condition or all of the following methods ,and without distinct deformation in appearance.
應滿足以下任何一個條件或以下所有方法, 并在外表上沒有明顯的變形
(1) solder bath method焊浴法
pre-heat :100 to 110℃ 30 sec
預熱
temperature ：270±5℃ 40sec
溫度
(2) reflow soldering method回流焊接方法
peak temperature :240±5℃ 3 to 5 sec
峰值溫度
temperature ：220±5℃ 40sec
溫度
the heating apparatus shall be the upper-heated oven and the temperature shall be
board surface temperature加熱裝置應上加熱烤箱和溫度應板表面溫度
the pt-smd shall be stored at standard atmospheric conditions for 1 hours, after which the measurements shall be made pt smd的應存儲在標準的大氣條件被測量后,為1小時
5-2-3 solvent resistance] 耐溶劑性
marking shall be legible標志應當清楚
without mechanical damage and distinct damage in appearance
沒有機械損傷和不同的損傷在外表上
immersion cleansing浸泡清洗
at room temperature ,90 sec in isopropyl alcohol在室溫下,浸漬90秒在異丙醇里面
5-2-4 drop test跌落測試
the pt-smd can resist to a 75cm drop on a 6mm thick steel sheet with no damage on it's characteristics, repeat three times pt smd能抗拒在75厘米的高度上跌落在6毫米厚鋼板上而不會產生任何損害,重復三次
5-2-5 vibration test振動試驗
the pt smd can resist to a vibration test with no damage on it's characteristic
pt smd可以抵抗一個振動測試而不會產生任何損害。
entire of frequency rang：10Hz to 55Hz to 10Hz for 1 min
整個頻響了：從10赫茲到55赫茲再到10赫茲在一分鐘之內
vibration amplitude ：1.5mm
振動振幅；振動強度
for a period of 2 hours in each of 3 mutual perpendicular directions
一段2小時在每3相互垂直的方向
5-2-6 shock test沖擊試驗；
the pt-smd can resist to a shock test with no damage on it's characteristic
pt smd能抗拒的一個沖擊試驗而不會產生任何損害
peak acceleration : 50G峰值加速度
duration of the pulse ：11ms
脈沖持續時間 ：11ms
each 3 times in each direction of 3 mutually perpendicular axis
每個3次在每個方向的3相互垂直軸
5-2-7 substrate bending基板彎曲測試
electrical characteristics shall be satisfied
電子特性良好的情況下
if there are electrodes on both surfaces, it shall satisty item 3-1 specifications on whichever surface it may be fixated on.
如果兩個表面上都有電極,應當在哪個廠家項3 - 1規范表面可能關注
bent width ：3mm 30 sec
彎曲的寬度
after above each item test ,valuation of item 3-1 should be within0.12
完成以上每一項測試后,評估項目3 - 1的公差應該在0.12%之內
5-3 Endurance 耐力
5-3-1 rapid change of temperature 溫度快速變化
Without distinct damage.
perform 5 cycles as follows 執行5周期,如下所示
(1)－55±5℃ for 30 min. -55±5℃的情況下測試30分鐘
(2) standard atmospheric conditions 2 to 3 min 標準大氣環境 2-3分鐘
(3)125±5℃ for 30 min 125±5℃的情況下測試30分鐘
(3)Standard atmospheric conditions 2 to 3 min 標準大氣環境 2-3分鐘
5-3-2 damp heat with load濕熱與負載測試
without distinct damage 沒有明顯的損傷
the marking shall be legible應當清楚的標記
60with relative humidity of 90% to 95% 60±5度的情況時保持相對濕度為90%至95%
input current 1ma for 1.5 hours on 30 minutes off ，1000+48/－0 hours
輸入電流1 ma保持1.5小時開啟然后后30分鐘關閉，1000±48/-0小時在70±5度
5-3-3 endurance 70℃度時耐力測試
without distinct damage沒有明顯的損傷
the marking shall be legible應當清楚的標記
input current 1ma for 1.5 hours on 30 minutes off ，1000+48/－0 hours at 70±5℃
輸入電流1 ma保持1.5小時開啟然后后30分鐘關閉，1000±48/-0小時在70±5度
5-3-4 high temperature test高溫試驗
without distinct damage沒有明顯的損傷
keep the pt sensor in 125 for 1000 hours
保持pt傳感器在125度的情況下為1000小時
5-3-5 low temperature test低溫試驗
without distinct damage沒有明顯的損傷
keep the pt sensor in -55for 1000 hours
保持pt傳感器在-55度的情況下1000小時
5-3-6 intermittently overload間歇性過載
input current 2.5 times the applied current for 1 sec. with pauses of 25 sec. for 1000 cycles
輸入電流為應用電流的2.5倍1秒鐘后停頓25秒,，進行1000次
after above each item test ,valuation of item 3-1 should be within0.12
在以上每一項測試完成后,評估項目3 - 1的公差應該在0.12%之內
6 packaging包裝
6-1-1 tape packaging dimensions帶條的包裝尺寸
6-1-2 reel dimensions一卷的尺寸
6-2 peel force of top cover tape上封帶剝落的力度
6-3 numbers of taping 4000 pieces/reel
繞盤的數量4000條
6-4 Marking
the following items shall be marked on the reel
下列事項,應當標明在卷上
（1） type designation 機型名稱
（2） quantity數量
（3） taping number繞盤的數量
（4）manufacturer's name 制造廠名
